All products

This range of products is what sets us apart, and has resulted in government awards for innovation & sustainability. Add sustainability to your monitoring well installations, and reduce your plastic waste footprint.

  • Disposable Bailer Cord Our disposable bailer cord is mainly used to deploy bailers and sleeve samplers. Made from polypropylene, it is well suitable for all types of ground water sampling. The 2.5mm diameter twine is packaged in a convenient 100m spool and also made in Australia. It has a manufacturers stated break load of approximately 195kg, so can be used for a range of applications.
  • The BioBailerTM is a quick and easy way to sample groundwater. Simply lower the bailer into your well and it fills with water as it submerses. When you pull up to retrieve the bailer the check-valve closes, trapping approximately 1L of water inside. BioBailersTM are made from landfill-biodegradable* PVC, and will only start to biodegrade once in a microbe rich environment such as a landfill. They do not require high oxygen or temperature to biodegrade such as in a commercial compost. Achieve the same groundwater sampling integrity as non-biodegradable bailers but more responsibly.
    Need to sample LNAPL / PSH? The easiest and most cost effective way is with the Hydrocarbon only or HC BioBailers. HC BioBailersTM allow you to collect floating LNAPL / PSH from a well, without collecting water. The ball valve is denser than LNAPL but lighter than water so it pushes water out of the bailer while keeping the LNAPL. These bailers also have a wider mouth than regular bailers, allowing you to collect more LNAPL with each bail. Like all BiobailersTM they are landfill-biodegradable.
  • Is sampling groundwater responsibly important to your business? ...then switch to 'BioTubing'. Our landfill-biodegradable tubing helps minimise plastic waste build-up in our landfills. BioTubing is made from landfill-biodegradable* LDPE (low density polyethylene) or HDPE (high density polyethylene), and will only start to biodegrade once in a microbe rich environment such as a landfill. It does not require high oxygen or temperature to biodegrade such as in a commercial compost. BioTubing enables you to achieve high sampling integrity plus operate more sustainably. Bonded Tubing for Low-Flow Sampling Our bonded tubing has the 1/4″ and 3/8″ tubes bonded together with a thin bridge and conveniently packaged on a 100m spool. The air and water lines have been bonded during the extrusion (manufacturing) process, and can be separated easily in the field to connect to a pump and controller fittings. It is recommended to scrape the bonding bridge clean with a knife to ensure a perfect seal. Many people prefer using bonded tubing as it can simplify pump deplyment and handling, and it can reduce the possibility of getting pumps stuck. The easiest way to manage your bonded tubing during pump depolyment, sampling, and storage, is by using the Rapid Reel tubing dispenser. Ultra-Clean BioTubing Our BioTubing has been independently tested for any leaching of 58 VOCs and 101 SVOCs.  The VOCs were tested using USEPA 8260B process and the semi VOCs via USEPA 8270. After tumbling for 18 hours the tubing showed 'non detect' on all the compounds analysed for. These compounds included Phthalates and PAHs. Data available on request. Waste Plastic Facts
    • In Australia alone over 1.5 million tons of plastic waste is disposed of each year, approximately 30 million tons in the USA, and about 5 million tons in the UK
    • Unfortunately most of this goes to landfill with only a small percentage being recycled
    • The use of plastic in western Europe and Australia is growing by about 4% each year
    • Plastic can take up to 500 years to decompose
    • Nearly every piece of plastic ever made still exists today
    • By using BioTubing and other landfill-biodegradable products you are helping to reduce the amount of plastic waste build-up in our landfills
    *Biodegradation has been verified by independent laboratory using ASTM D5511 for anaerobic landfill conditions. Independent laboratory testing confirms that our BioTubing is PFC/PFAS-free, based on analysis for 28 different PFCs at extremely low detection limits. For sampling on PFAS sites HDPE tubing is often prefered. HDPE tubing is available in 1/4", 3/8", and 5/8" OD sizes. Click the 'Ordering Information' tab to see all available options for BioTubing.
  • The fox whistle is the ultimate low cost tool you can use for measuring depth to water.  Our fox whistle is made from stainless steel, is 20mm in diameter and 200mm long.  Air is pushed through the hole in the fox whistle and when it comes into contact with water, it makes a whistling sound. A 30m tape on a windup reel is also available to order as well. Please Note - Maximum depth recommended is approximately 20m, otherwise you may not hear the whistle. Also, not recommended for use in noisy environments such as a busy road or noisy site, as again you may not hear the whistle.    
  • Measure the pH in soil easily using the Milwaukee Instruments MW101-SOIL pH meter kit. This portable meter is also suitable for use in a wide range of applications such as education, agriculture and horticulture, as well as water and environmental analysis.

    MW101 performs pH measurements with a 0.01 pH resolution and with manual temperature compensation.The meter is supplied with pH electrode and calibration solutions.

  • A better designed well cover using recycled plastic for sustainability The Nondo Eco 180 well cover is designed with sustainability in mind. The reuse of current resources and the conservation of our future resources are fundamental to all our design concepts where practical. The Nondo Eco 180 is made entirely from recycled plastic and has been tested to meet load bearing requirements for traffic suitability for Australian Standard AS3996 Class D.
    • One piece gasket seals both the lid and around bolt holes heads to prevent surface water ingress, and completely seals the well
    • 2 stainless steel bolts, counter sunk with 8mm hex for secure lid clamp down
    • 180mm diameter OD, large 146mm ID, 122mm between bolt holes
    • High strength recycled plastic (HDPE & Delrin) is resistant to petroleum products
    • Unlike steel, recycled plastic will never rust
    • Lower cost than traditional cast iron covers
    • Light weight only 1.2kg but rated for heavy trucks
    • Load tested to AS3996 Class D traffic rating
    • Ideal for 50mm monitoring wells
    • The all recycled plastic Eco180 will never rust leaving your installation work always looking good
    • No more finger crushing under heavy lids, the Eco180 lid is lightweight with no sharp edges
  • The Nondo Mini monitoring well cover is our budget bolt-down, flush mounted well cover. It is designed to be used for monitoring wells or for soil vapour installations. With the bolts outside the inner working space, the Nondo Mini gives you maximum internal room for such a small cover. Features:
    • 2 counter-sunk flush bolts to reduce the risk of trip hazards, as there are no protruding bolt heads
    • High strength cast iron in black epoxy
    • White powder coated lid
    • Large internal opening of 124mm (98mm Bolt head clearance)
    • Small 150mm outside diameter
    • Ideal for standard 50mm monitoring wells or soil vapour implants
     
  • The Nondo Safety Lifter / Multi Tool enables a safe way to remove our steel well cover lids and comes with all the necessary allen keys for our well covers and TriCap well plug.
  • A medium sized well cover with some big features The Nondo180 monitoring well cover contains a high quality machined cast iron lid and base, with a strong plastic skirt. It is ideal for 50mm monitoring wells and has been tested to exceed load bearing requirements for traffic suitability for Australian Standard AS3996 Class D. The small 180mm OD makes it ideal for drillers who typically use a 200mm concrete corer.
  • Silicone Peristaltic Tubing is flexible and soft, making it suitable for peristaltic pumps. FieldTech Solutions Peristaltic Silicone Pump tubing is available in 15 m individually wrapped coils, available in these sizes:
    • 1/8" ID / 1/4" OD, 15m roll
    • 4.8mm ID x 9.5mm OD, 15m roll, for use with Geotech Peristaltic Pump
    • 1/4" ID / 3/8" OD, 15.2m roll
    • 5/16" ID / 1/2" OD (7.9mm ID x 12.7mm OD) 15m roll
  • Simply the best way to manage tubing for low-flow groundwater sampling

    • The Rapid Reel is a simple cardboard tubing dispenser for our biodegradable tubing for low-flow sampling
    • Low-flow sampling has just been made easier
    • Simply connect the tubing to your sampling pump then deploy down the well, letting the tubing flow easily out of the Rapid Reel box
    • Clean and simple
    Testimonials:

    "I used the rapid reel last time I was groundwater sampling and thought it was great. Made life so much easier, especially on the deep wells." (Samantha Walsh - Landserv)

    “I have to say, when I saw the rapid reel on your website, memories sprung to mind of countless times spent fighting soggy cardboard reels and unruly tubing. The Rapid Reel did live up to my expectations. It definitely helped keep my ute/workspace tidier, and it was quicker and easier to reel out the quantity I needed." (Anonymous - Ventia)
  • Low Cost, No Purge Groundwater Sampler These types of samplers are fast becoming a popular method for groundwater sampling on many Australian sites. Sleeve samplers make groundwater sampling a simple, three-step operation that can be more effective than purging or low-flow sampling. The low-cost, disposable sleeve captures a core of water from any discrete interval in the screened portion of the well with no change in water level and minimal disturbance to the water column. The sleeve is sealed except during sample collection, then re-seals itself, assuring that a formation quality sample is recovered. The tripod stand option provides a convenient place to hang a full sampler while filling sample bottles. Independent laboratory testing confirms that sleeve samplers are PFC/PFAS-free, based on analysis for 28 different PFCs at extremely low detection limits.
  • Well Development or Sampling The stainless steel bailer is ideal for both groundwater sampling & well development. The all stainless steel construction and check ball allows for rapid decontamination between wells. The tapered top is designed to avoid hang ups in the well, and smooth raising & lowering. A 45mm diameter enables it to be used in standard 50mm monitoring wells. Reusable equipment such as this helps reduce the amount of disposable waste, and adds sustainability to your operation.  

Title

Go to Top