-
When direct push sampling in sands or loose soils, a core catcher is recommended to be used in the BioLiner, which will stop the soil sample from falling out when retrieving from depth. Our core catchers are 100% recycled plastic and landfill-biodegradable. -
Biodegradable Cleaning Concentrate Decon 90 is a highly effective decontamination and cleaning liquid which is also biodegradable. It can be used to clean pumps, bailers, tubing, soil augers, or any sampling equipment where cross-contamination between sampling locations is a concern. Decon 90 is highly effective on petroleum contamination such as fuels and oils, but also Strontium 90, Iodine 131, Carbon 14, Phosphorus 32, Au 198, Hg 203, Translutonium, Tantalum and radiocarbon are all handled by Decon 90. It also caters for a wide range of problem contaminants including: Abrasives, agar algae, apiezon get bacteria, blood, distillation residues, latex, protein complexes, pus, tar, sera, silicone, grease and oil, reagents and more. Download MSDS -
Vertical Downhole Inspection Camera The dipper-See EXAMINER vertical downhole inspection camera is a cost-effective way for people performing well inspections, maintenance, and installation to do their jobs quickly and accurately. The dipper-See EXAMINER comes with everything a well inspector, well driller, or hydrogeologist needs to do more work in less time. The Heron dipper-See EXAMINER is a robust and cost effective vertical downhole inspection camera. Designed with portability in mind, this self-contained unit is ideal for viewing in wells, drains, vertical shafts, open bodies of water, boreholes and narrow tubes over 25mm (1”) in diameter.* The dipper-See EXAMINER and the included accessories are easily transported in the provided super tough wheeled carry case and accessory case, ideal for protecting your investment from the elements. The adjustable positioning arm, conveniently attached to the frame, offers an ergonomic solution for adjusting the monitor for viewing the High Definition (HD) display screen at different angles and varied lighting conditions. The monitor conveniently houses all of the controls on the front of the panel. Record the video/audio on the SD card provided with the DVR, for easy transfer of video to another device. Please note that the monitor is rated IP65 and should be covered during wet or inclement weather and protected against direct exposure to water projection (spraying). The HD, detachable See-120 camera probe is designed to work in the harshest environments and stand up to the most rigorous use. The camera probe can be easily removed at the link connection for field replacement and for future camera upgrades. The built-in hanger on the frame can support the unit at the top of the well, allowing for hands-free viewing while in the field. Available in 150m or 500ft tape lengths only* Download Brochure
-
The dipperLog VENTED+ is a reliable, cost-effective solution for measuring groundwater levels and temperature in wells, boreholes and open bodies of water. The dipperLog VENTED+, incorporates a gauged transducer that measures pressure exempt from barometric influences which is ideal to use in both long and short-term monitoring. The dipperLog VENTED+ is removable from the vented cable, allowing easy field replacement. Just connect your laptop or Windows Tablet at the wellhead. Download Brochure
-
Discoverer Core Sample Trays Made in Australia, the Discoverer® core trays are rugged and lightweight. They are now available in black recycled plastic too and are also fully recyclable. Safety: The Discoverer® plastic core trays remain relatively cool to touch when left outside, unlike metal trays. Therefore no more painful burns when handling core trays. Rounded edges mean no more dangerous sharp edges, leading to improved safety when handling. Built in Handles on both ends of the trays provide safe and easy use when handling. Being manufactured with a one piece mold means no unusable trays in use, reducing the chance of workplace related injuries. Superior Strength and Durability: Made from a one piece mold, meaning no pop rivets and welds which increases the products strength and importantly no sharp edges. The Discoverer® is made using the highest UV stabilized polypropylene available making it exceptionally durable in any harsh mining or exploration environment. Manufactured from exceptional quality raw materials, which makes it extremely resistant to impact and crushing. The Discoverer® Sub Zero is manufactured for use in freezing conditions and trays are tested to minus 50°C. Ease of use: A bold start indicator has been designed to make it absolutely clear to the driller at which end they should commence loading the core from, eliminating possible errors in the logging process. The trays are colour coded, allowing for quick and easy identification of the different sizes both in storage and out in the field and when re-ordering. The Discoverer® has a built in ID Tag area and optional aluminum tag inserts providing a permanent record of contents. The Discoverer® has standardized sizing. The majority of sizes used in the environmental, mining and exploration industries are H, N, P & B core diameters. Lengths are standardised making all the trays 1m (3.49ft) long. Maintain Your Core Integrity: The materials used during manufacturing have a high level of resistance to organic chemicals that are found in some drill core recovery, meaning your core won’t become contaminated. The Discoverer® is non-magnetic and will not corrode keeping your core free from magnetic susceptibility when testing and ensures no corrosion of the trays occur. The unique raised ribbed design helps to retain the quality of your core by improving drainage. The Discoverer® core trays cannot be affected by insect infestations like wooden core boxes as the plastic is not penetrable. The plastic used in the core boxes will not migrate or leach into your core samples. The Discoverer® core trays have a range of accessories available and one of these is the custom made lid which assists to maintain your core’s integrity at all times. Only the Discoverer® core trays have unique a stacking capability, which allows the trays to stack perfectly on top of each other, loaded with core without touching the tray below. This means that your core is stored without interference, helping to retain the quality of the core. -
Bioremediation Products Fieldtech Solutions is proud to represent EOS Remediation in Australia. EOS Remediation is the leading provider of bioremediation products that re-engineer the groundwater environment, transforming contaminants into non-toxic end products. EOS Remediation’s products are ecologically sustainable (USDA Certified BioPreferred Products), and cost-effective with proven results. Most of these products are being manufactured locally here in Australia. Their diverse family of products, driven by extensive research and development, are available to meet a variety of project needs. If you have a current bioremediation project, and you are you looking to calculate the volume of EOS product required, we request that you please fill in the Site Evalution Form and email back to us so we can help. Not all fields may be known but please fill in as much information as you can. Download Site Evaluation Form -
These convenient socks pre-filled with approximately 312.5 g of EOx® Powder. They are 38mm diameter, suitable for 50mm wells or larger. EOx® is a granular powder of calcium peroxide that provides slow and steady oxygen release for long-term aerobic biodegradation. Suitable for enhanced aerobic biodegradation of BTEX, PAHs, DRO, MTBE, VC and other complex contaminants in soil and groundwater. -
VOC Sampling in Water or Soil Gas Sampling FEP or PTFE tubing is commonly referred to as 'Teflon® Tubing'. Teflon® is a registered trademark of DuPont, and they were the first company to discover these types of plastics in the 1940s. Fieldtech Solutions stocks clear FEP tubing for soil gas sampling in 1/4" OD size in 15m and 60m rolls. We can also supply a range of PTFE in larger diameter sizes. -
Filter sock can be used to protect groundwater wells from infiltration of fine silt and sediment. Made from polyester and with a 340 micron pore size. Available to suit 50mm, or 100mm to 150mm monitoring well screen. Simply sleeve the filter sock over the pvc screen before installation. -
The Flexipoint is pointed bottom end cap made from recycled plastic. It is long enough to be installed on either the male or female threaded end of the 50mm slotted PVC screen, without a need to cut off the female thread. -
The fox whistle is the ultimate low cost tool you can use for measuring depth to water. Our fox whistle is made from stainless steel, is 20mm in diameter and 200mm long. Air is pushed through the hole in the fox whistle and when it comes into contact with water, it makes a whistling sound. A 30m tape on a windup reel is also available to order as well. Please Note - Maximum depth recommended is approximately 20m, otherwise you may not hear the whistle. Also, not recommended for use in noisy environments such as a busy road or noisy site, as again you may not hear the whistle. -
Corrosion Protection for Standpipe Covers: Certain site requirements or tender specifications require galvonised steel. The standpipe also has a unique non-binding swivel hinge for long life, which is protected from rain. Traditional looking standpipe covers have hinges which are exposed to the elements and therefore prone to corrosion and eventually seizing up or dropping off. Our unique design has addressed this weakness. The 100mm square galvanised steel standpipe covers have a unique non-binding 'hidden hinge' design which provides a rain proof cover. These low-cost covers have a galvanised / silver finish for corrosion protection. -
The Heron Instruments barLog, barometric logger is used to automatically compensate readings stored on the dipperLog for changes in barometric pressure. The barLog, with readings every 1 hour and a memory capacity of 32,000 data points, is recommended for long term monitoring or where more than one logger is deployed withing in a 5 km radius. The dedicated, intuitive software makes the dipperLog quick and easy to program and launch. Simply recover your data, save your findings in a tabular display and graph, view both parameters side by side in a split screen. Use the Heron Instruments’ barLog alongside your dipperLog Groundwater Data Logger for the most accurate data possible. Add a barLog to your quote for the dipperLog TOUGH, dipperLog 64, or dipperLog 32. Download Brochure -
Conductivity, Temperature & Static Levels The Conductivity Plus enables accurate measurements of conductivity, water levels and temperatures in wells, boreholes, stand pipes and estuaries where salt water intrusion and contamination levels become a concern. Conductivity can be an early indicator of change in a water system due to fluctuations of salinity in water levels. The premium padded carry case comes included to protect your precision instrument from the elements. The high tensile steel core measuring tape is tested for stretch resistance to ASME standards and is ideal for profiling up to 50˚C. An LCD screen displays conductivity values up to 80,000 µS and temperature range from 0˚C – 50˚C. The conductance temperature compensation coefficient is 2.0%. Calibration of the conductivity plus is easy using readily available 1413, 5000, 12880, 111800 uS solutions, and up to 4 calibration points can be utilised. The Conductivity Plus provides a higher range of up to 250,000 μS/cm, which is the highest conductivity range on the market. -
The Heron dipper-T water level meter is designed for well drillers, consultants, and hydrogeologists all across the globe. The dipper-T is a rugged and dependable water level meter made from high quality materials, easy to use for a wide variety of applications. The dipper-T is capable of measuring both static and falling head levels. Static mode is used for measuring the depth of water in wells, boreholes and standpipes. DrawDown mode is used for measuring falling water levels during purging, well development and for low flow sampling; helping to protect your pump from damage caused by dry running. The Heron dipper-T is renowned for its premium, polyethylene coated yellow steel tape accuracy in measuring depth to water. Available in your choice of either metric or engineering scale. The highest accuracy begins with a top quality, heavy duty tape. Each tape is tested to ensure compliance with appropriate ASME standards. These tough tapes have a breaking load of over 150 kg. The tape is made from high tensile steel, ensuring resistance to stretching even at abnormal loads. Everything on the unit from the ergonomic vinyl carry handle to the easy clean, full depth stainless steel probe has been carefully designed to give you the very best water level meter. Each unit includes a sturdy padded nylon carrying bag. Drawdown Feature For Low-Flow Sampling With a touch of a button the unit changes from static to drawdown mode; a dual function unit at an affordable price. The dipper-T in drawdown mode is ideally suited for low-flow groundwater sampling. During sampling the drawdown level needs to be monitored closely so that it does not fall below the pump inlet. If the drawdown alarm sounds then the user can quickly slow the pumping rate or stop the pump temporarily and allow the well to recover. The drawdown feature may be used for measuring falling water levels during purging and well development, helping to protect electrical pumps from damage caused by dry running. The Well Casing Indicator Probe is used to measure the depth of metal casing in wells and boreholes from 50mm in diameter and upward. The Well Casing Indicator Probe works using magnetism. While the probe sits within the magnetic field of the steel casing, an auditory and visual signal is active. When the probe leaves the magnetic field the signal stops. Note the condition of the well for accurate readings. The Well Depth Indicator Probe (or bottom detector) is used to measure the full depth in wells and boreholes. The Well Depth Indicator Probe uses a pressure sensitive plunger to measure the distance to the bottom of the well. When the Well Depth Indicator Probe reaches the bottom of the well, the plunger enters the probe body closing a switch, initiating an audible and visual signal at the top of the well.
