-
The 100mm well plug is manufactured from a recycled composite glass filled polymer that will not corrode, and is stronger than steel, pound for pound. The center locking mechanism allows a padlock to be secured in a variety of positions, offering more flexibility in applications with limited space. Constructed of recycled composite glass-filled polymer which is stronger than steel pound for pound, the 100mm well plug is designed for years of worry-free use. The wing nut design with a recessed grip allows a padlock (not included) to be easily installed. The 100mm well plug has a tethering attachment at the base for use with a variety of instruments, features no metal parts, and can be disassembled for easy decontamination. The standard well plug and GasCap is available for 100mm wells. -
The WC25Gas has a quick connect gas fitting and dust cap installed on the top, enabling gas in the well to be monitored or sampled with a gas instrument or suitable pump. -
The WC100GAS has a quick connect gas fitting and dust cap installed on the top, enabling gas in the well to be monitored or sampled with a gas instrument or suitable pump. The WC100Gas can also be locked in place with a padlock or by using a security screw or both for extra security. It has a large wing nut, designed to make it easier to tighten or release the plug. It comes with a ring below so you can hang/attach tubing, skimmers or sleeve samplers in the well. -
The Waterra PowerPack PP1 provides the mechanical actuation for pumping with inertial pumps to depths of over 60m, in a fully portable, single operator power unit. At 13 kg, the PowerPack PP1 provides outstanding pumping performance. The PP1 is powerful enough to lift water from over 60m depth using the Standard Flow System, and is so compact that it fits onto a back-pack frame. The PowerPack PP1 incorporates clamps for Waterra High Flow and Standard tubing sizes (adaptors are available for smaller tubes). A Honda GX-25 series, 1.0 horsepower, 4 stroke, gasoline motor powers this device, which can run for approximately 1 hour without refuelling. -
The Hydrolift is a portable, 240v operated electric device that is used to automate the operation of the Waterra Pump System. This actuator is perfect for purging and sampling 50mm diameter monitoring wells up to 60m deep. In special circumstances it can lift up to 90m. This electrical Tubing Actuator is optimized to operate with the Standard Flow System up to its maximum effective depth and will operate with the High Flow System up to a depth of 45m. This Tubing Actuator is the ideal choice for the frequent user of the Waterra Pumping System with moderate to extreme pumping requirements (Low, Standard and High Flow). Using the Hydrolift will result in a big boost to your field sampling program. The Hydrolift is powered by a 3/4 horsepower (560 watts) electric motor and generates a 4 inch (10 cm) stroke at up to 140 cycles per minute. The Hydrolift weighs about 16 kg and requires an electrical power supply of at least 1000 watts. *Please note the Hydrolift requires a generator to power it. See image 2 for an animation on how the system works. -
Turn your BioTubing into a groundwater pump Waterra footvalves or inertial pumps have long been a reliable and effective way to sample groundwater. They consist of a one-way checkvalve which connects to a length of HDPE BioTubing. Oscillating the tubing up and down in the well produces a flow of water. The tubing can also be connected to external pumps such as the Waterra Powerpack or PowerPump. Waterra footvalves can be a great sampling solution for narrow diameter wells. Fieldtech Solutions stock a range of the most popular sizes such as the D25, D32, and D16 footvalves. Each of these can connect to our BioTubing which allows it to function as a manual groundwater pump.
-
The Waterra 1 UP Peristaltic Sampling Pump can be powered by 110 and 220V AC, external 12VDC or its 12V internal battery. Suction lifts up to 8.5m. 4 Battery Choices LIFE Batteries are Lithium Iron Phosphate batteries that weigh about one half the weight of the SLA (Sealed Lead Acid) batteries. LIFE batteries a have better discharge curve, maintaining higher voltages for longer. Available in 20 Ahr and 12 Ahr formats. A LIFE 12 Ahr 1 UP Pump weighs less than 8.1kg and the 20 AHr unit weighs less than 9.5kg. SLA Batteries are Sealed Lead Acid conventional batteries that are a less expensive than LIFE batteries, but weigh about twice as much. Available in 20 Ahr and 12 Ahr formats. -
Landfill Leachate, and Remediation Pumps: - Fully Automatic, Float Actuated Pumps The Viridian range of pumps (VP Pumps) are designed specifically for pumping landfill leachate, landfill gas condensate and contaminated groundwater. As no down-well level control device is required, the VP pumps lend themselves to being part of a multi-well pumping system. This makes overall system control very simple. With minimal training, the site personnel quickly become confident with both pump and system. Available in a range of sizes and variations, and capable of discharging up to 1.1 litres of liquid per cycle. The bottom-filling versions are specifically designed for the harsh conditions of pumping landfill leachate. Available as a top loading version, for groundwater remediation applications, as well as a short version, and the 'LDD' (low drawdown) when minimum liquid head is vital. The VP2 and VP3 range has a reduced discharge capacity but it is ideal for smaller borehole sizes. As the VP pumps are driven by compressed air, a multi-well system would have an air-main connecting each pump - a far safer power source than electricity cables and less costly. VP Pumps also do not require an external form of control. Pulse Counters, for volume and flow rate measurement also available. Download Brochure
VP Pumps Range
-
Reduce filtering costs with the 150ml PES (Polyethersulfone) vacuum filter flask. The Vacccum Filter Flasks include a bottle-top filter and a receiving flask, and PES 0.45u bottle-top filters. Comes in a carton of 12.- 0.45 micron filter membrane
- Connects easily to Mityvac Hand Pump
- Available in cartons of 12
-
A Solution for Legacy Covers The universal FB180 lid is designed to fit legacy well covers from other manufacturers which are no longer in production. This includes the 'EE' FB180, and other similar covers. Sometimes lids can go missing or get broken on site over the years. Rather than breaking up the concrete to install a new cover, often involving costly traffic management, you can now simply replace the lid. Suitable bolts and an oring is also supplied with the lid. Please note it is not a replacement lid for our Nondo covers. -
The Shelby sampler is a thin-walled soil sampling system. The system is used to sample soils that are particularly sensitive to sampling disturbance, as it has a very low wall thickness-to-sample area ratio. The sampler consists of a thin walled steel tube whose lower end is shaped to form a cutting edge. Fieldtech Solutions is now stocking U63 and U50 Shelby Tubes and drive heads. Drive Heads are available in AW, AWJ, or NWJ box threads. -
The TriCap-GAS has a quick connect gas fitting and dust cap installed on the top, enabling gas in the well to be monitored or sampled with a gas instrument or suitable pump. The TriCapGas can also be locked in place with a padlock or by using a security screw or both for extra security. The TriCap has a partially hollow shaft that intersects a horizontal side hole near the bottom. This allows the well gas to be drawn in through the side hole and out the top. The side hole also serves to hang sampling or monitoring devices off the bottom of the cap while at the same time gas samples can be taken out through the shaft and out the gas quick connect fitting. -
The TriCap-LOG has been specifically designed for use with submersible groundwater level logging devices. Just like the TriCap-GAS, the hollow shaft intersects a horizontal side hole through the shaft near the bottom. An elbow fitting installed in the top enables the well to be vented to the atmosphere. Attach optional tubing to allow the vent port to be raised up above any surface water and prevent it from flowing into the well through the vent. A stainless spring clip is also provided for easy logger attachment. The Tricap-Log is the perfect choice for use with submersible groundwater logging devices. It features an elbow fitting which vents the well to atmosphere, and a unique stainless spring clip for easy logger attachment. The TriCap is made from recycled plastic for sustainability and enables a groundwater monitoring well to be sealed and locked. -
An environmental monitoring well cap or plug made from post-consumer recycled plastic for sustainability. The TriCap provides:- Strong protection for your monitoring wells
- Self locking option with additional stainless steel security bolt, using a special key tool or allen key
- Hanger cable holes on bottom end of shaft
- Fully sustainable, made from recycled plastic waste
- Wide rubber ring provides a water tight seal
- Also available in orange
-
This all pneumatic box will shut off the air supply to down-hole pumps when the tank, drum or IBC becomes full. This prevents overfilling of the drum and creating a spill. Ideal for LNAPL recovery projects. Comprising of a separate control box and tank sensor, the control box can be mounted separately from the drum. The tank sensor is screwed into the drum and connected to the control box by a small air hose. Being all pneumatic makes this inherently intrinsically safe.
-
Using syringes for groundwater filtration in the field is a popular low-cost option. It can be an ideal choice if you are not using a pump, and have a manual device such as a bailer. When using a syringe 50ml at a time can be pushed through a filter. Small low-capacity filters can be used where turbidity is low. However if turbidity is high then it may be better to use a high capacity filter such as the AquaPore Biodegradable Filter Capsule. Syriges are available in luer-lock, catheter tipped, or eccentric tipped varieties. -
The Swing Sampler enables you to reach out up to 2.4m from a river bank or shore to take a 1.2L surface water sample. It can also be used for reaching into tanks, drums, or any difficult locations with up to 90 degrees rotation on the free-swinging head. The sample jar has a volume of 1.2L and can be re-used (recommended to use Decon 90 to clean between samples). The re-useable sample jar is made from landfill-biodegradable plastic, so when it eventually gets disposed to a landfill it will biodegrade. -
-
A New Concept for Standpipe Covers - Hidden Hinge Design The 100mm square yellow steel standpipe cover has a unique hidden hinge design which provides a rain proof cover. Traditional looking standpipe covers have hinges which are exposed to the elements and therefore prone to corrosion and eventually seizing up or dropping off. The unique design has addressed this weakness. These low-cost covers have a bright yellow powder coated finish, and are also available as galvanised. -
These Standpipe Covers are designed to be simple and robust, with a unique large clearance hinge that will not rust and bind, and an attractive bright blue powder coated finish. A padlock can also be used on the lid for extra security. 3 different sizes to choose from:- SPRB114 - 114mm diameter
- SPRB165 - 165mm diameter
- SPRB219 - 219mm diameter
-
Lightweight and Rugged The SP155 is the largest of our plastic Standpipe Covers. With a 145mm ID it is ideal for LFG installations where using a 'Gas Clam' instrument for continuous LFG monitoring may be desired.- Ideal for 100mm well installations
- Plastic standpipe cover, will not rust
- A wider opening (145mm ID) for use with a "Gasclam" or other instrumentation
- Strong protection for your monitoring wells with a professional, stylist finish
- High security with one way security screws to deter tampering
- High visibility yellow colour
- Safer to use with no sharp steel edges
-
Made from post-consumer recycled plastic (i.e. bottles and other plastic waste sent for recycling), these stylish upright covers give your monitoring well a professional finish. By purchasing products made from recycled plastic you are supporting the plastic recycling industry. The reuse of current resources and the conservation of our future resources are fundamental to all our design concepts where practical. The Heavy Duty Standpipe Cover range is thick walled (23mm) HDPE (high density polyethylene) to give you a very strong, chemically inert and petroleum resistant well cover. They are available in blue or black with large bright orange reflectors for high visibility.
-
Our largest standpipe cover is the all recycled plastic SP272. This round standpipe cover has a 250mm internal diameter which means there's even enough room for 150mm PVC well installations. The mottled, multi-coloured look is a result of the post-consumer plastic items being melted together to make a unique and great looking cover. Ideal for landfill or remediation applications where a larger diameter cover is often desired. By purchasing products made from recycled plastic you are supporting the plastic recycling industry. The reuse of current resources and the conservation of our future resources are fundamental to all our design concepts where practical. -
Well Development or Sampling The stainless steel bailer is ideal for both groundwater sampling & well development. The all stainless steel construction and check ball allows for rapid decontamination between wells. The tapered top is designed to avoid hang ups in the well, and smooth raising & lowering. A 45mm diameter enables it to be used in standard 50mm monitoring wells. Reusable equipment such as this helps reduce the amount of disposable waste, and adds sustainability to your operation. -
Made from post-consumer recycled plastic (i.e. bottles and other plastic waste sent for recycling), these stylish upright covers give your monitoring well a professional finish. By purchasing products made from recycled plastic you are supporting the plastic recycling industry. The reuse of current resources and the conservation of our future resources are fundamental to all our design concepts where practical. The Economy Standpipe Cover is a thinner walled option for budget limited projects. They have a recycled plastic inner core and a bright yellow outer layer for high visibility.
-
Biodegradable Sleeving for Sonic Rigs Now you can reduce your plastic footprint on sonic rig sampling jobs by using landfill-biodegradable HDPE sleeving. The clear sleeving has a 203mm lay-flat width, and a thickness of 150 micron. Suitable for Geoprobe, Boart Longyear, and any other sonic rigs which use 8" lay-flay sleeving. -
Soil Vapour Implants can be used for permanent or temporary installations. They can be used for soil gas sampling, air sparging, and even groundwater sampling. They are an accurate and economical way to sample soil vapour. These popular mesh implants come with a barb on top to connect to 1/4” Teflon® tubing. A threaded bottom connection allows connection to a weight to pull the implant down during installation. The implant mesh allows easy passage of the soil vapours to pass in from the target zone into the tubing. The barb allows leak free and tool-less connection of the Teflon® or other similar tubing up to the surface. A range of surface connection fittings are available to provide flexibility to various connection methods at the surface. Installation involves drilling or augering a hole down to the target zone, placing in an implant with connected tubing. Then backfilling around the implant with sand and gravel pack across the target zone. Finally filling back in with soil and or bentonite to make a seal from the surface. The top end of the tubing is where the soil vapour sample is drawn from. When not in use keep this capped.Do I need a weight? Due to the coiled Teflon® tubing acting like a spring, it can bind on the sides of the bore. For shallow installations of a few metres, a weight may not be necessary. For deeper installations a weight is recommended to pull the implant down to the bottom.
-
-
Our 1 litre slug is made for performing a 'slug test', which enables hydraulic conductivity estimation in monitoring wells. Designed to fit within a 50mm well and displace 1L of water. Custom sizes can also be made for larger wells, or multiple slugs can be used together to displace more water in the monitoring wells. -
Low Cost, No Purge Groundwater Sampler These types of samplers are fast becoming a popular method for groundwater sampling on many Australian sites. Sleeve samplers make groundwater sampling a simple, three-step operation that can be more effective than purging or low-flow sampling. The low-cost, disposable sleeve captures a core of water from any discrete interval in the screened portion of the well with no change in water level and minimal disturbance to the water column. The sleeve is sealed except during sample collection, then re-seals itself, assuring that a formation quality sample is recovered. The tripod stand option provides a convenient place to hang a full sampler while filling sample bottles. Independent laboratory testing confirms that sleeve samplers are PFC/PFAS-free, based on analysis for 28 different PFCs at extremely low detection limits. -
LNAPL Skimming Socks for 50mm Monitoring Wells The easiest way to remove small amounts of fuels from monitoring wells is with these low-cost skimming socks. Each sock holds about 500ml.
Our Products
Copyright © 2024 FieldTech Solutions. All rights reserved.
